Painting FRESKO Interior Extra

Type: Water-dispersive paint for interior work «FRESKO Interior Extra» is a suspension of pigments and fillers in aqueous dispersion of acrylic copolymers with the addition of auxiliary substances. Paints can produce colors under catalogs NCS, RAL, and others. Release of paints of other colors according to the samples provided by the customer color. Advantages: Water-borne paint for interior work «FRESKO Interior Extra» - environmentally friendly, odorless after drying, form a smooth, velvety, matt surface. Paints have good hiding power, high brightness, opacity, and warrants their thixotropy smudge deposition and uniformity ensures uniformity and coating thickness. Paints resistant to slight mechanical stress, have good adhesion to concrete, brick, drywall and stucco surfaces. Formed paint coating "breathes" without Melita, resistant to dry abrasion. Colours are resistant to mold and mildew. Surface preparation: The surface must be clean, dry, sound, have a good load-bearing capacity and can not contain substances that reduce adhesion (release agents). Fresh mineral surfaces (plaster, putty) before painting should be soaked for at least 28 days at a temperature of not less than 10 ° C, the permissible residual moisture reason - not more than 8%. The ambient temperature and the surface should not be below 7 ° C plus. If you deviate from these recommendations may occur deterioration in the performance and manufacturability of applying paint. Old, firmly hold the paint coating is recommended to wash with soap and water or detergent or soda solution (1 tablespoon per 1 liter of water) and then with clean water and dry. Surfaces previously painted with mineral paints, a loose cover, loose material base, chalk or lime-chalk coating completely removed by mechanical means. Peeled surface and coating defects are aligned plaster solution or polymer fillers, sanded and cleaned of abrasive residues. Surfaces with efflorescence, it is necessary to clean the dry method (brush). In operation the surfaces of this type can not ensure the durability of the coating, as possible re-emergence of salt deposits and thereby failure of adhesion coating to the substrate. Land surface affected by mold or fungus should be cleaned with steel brushes and then apply the primer «FRESKO Antiseptic Ultra» (TU BY 500021625.208), to prevent the re-emergence of micro-organisms. On the metal parts (valves, nail heads, etc.) is applied primer "Akvapraym" (TU BY 500021625.125) or primer "LidAkril" (TU BY 500021625.124), or priming enamel "Ekolyuks" (TU BY 500021625.145) in order to avoid rust. For priming and leveling the absorbency, reducing ink consumption, increasing the adhesion and strength of the substrate on the prepared surface is recommended «FRESKO Imprelid» priming or deep penetration primer «FRESKO Imprelid Ultra» (to strengthen the loose, porous, fragile and grinding surfaces). The application and drying primers is carried out in accordance with the recommendations in the primer data (TU BY 500021625.112). For priming and leveling the absorbency as a primer layer can be used as a paint «FRESKO Interior Extra» and «FRESKO Interior», diluted with water at a ratio of 3: 1. the primer drying time at least 2 hours at a temperature (20 ± 2) ° C and a relative humidity of 65%. Recommendations on Application: before applying the paint should be thoroughly mixed. At the base of the prepared paint is applied by brush, roller or airless spray with an initial viscosity of at least two layers, not including the primer. If necessary, the paint is diluted with water to 5% by weight of the ink (color ink when diluted to avoid all colors equal amount of capacitance added water). To prevent the formation of visible joints and bands of individual sections of the treated surface, the paint should be applied in a single pass "wet on wet" technique over the entire surface, thoroughly distributing it concludes roller rolled in one direction with the same force. Sloyami- intermediate drying between at least 2 hours at a temperature (20 ± 2) ° C and a relative humidity of 65%. Paint drying time depends on the temperature, humidity and other factors.