Enamel PF-115 U

Sector: Paints a & Lacquers
Price: Contract Price
Minimum Order: От 600 кг.
Packaging: Tin
Terms of Delivery: FCA Lida
Full Product Information:
Type: Enamel PF-115 "Y" is a suspension of pigments and fillers in a modified alkyd varnish and a solvent with the addition of special additives. Advantages: enamel coating is elastic, has a high hardness and good adhesion to metal surfaces; enamel single component, it is stable during storage, has excellent paint properties, a small flow rate that creates and saves the convenience in application, the enamel coating dries quickly to form a flat, smooth surface; Surface preparation: metal surface before applying the enamel must be thoroughly cleaned from dust, rust, scale and other debris, allowed to dry, cleaned sandpaper (allowed to use sandpaper grit size 4 or 5 in accordance with GOST 6456), degreased and primed primers GF-0119 (GOST 23343), GF-021 (GOST 25129), GF-021 "L" (TU RB 500021625.096) or primer fast drying "Fastpraym" (TU BY 500021625.177-2011). Previously painted surfaces must be cleaned of dust, grease, dry, grind, degrease and make a test staining. In case of blistering or peeling old paint must be removed. To avoid moisture condensation substrate temperature should be above the dew point temperature of not less than 3? C. Unpainted wooden surfaces must be cleaned of tar, dry, clean lint remover sandpaper (allowed to use sandpaper grit size 4 or 5 in accordance with GOST 6456) and remove dust. To reduce the consumption of enamel and increase the quality of finishing, unpainted surface is recommended pre-primed with GF-021 (GOST 25129) or other alkyd primer, clean the abrasive cloth, avoiding stripping to a wooden surface. With the previously painted surface must remove various impurities, completely remove loose coating, the surface is sanded and de-dusted. Do not be painted during precipitation, as well as on wet and icy surfaces. Coating: enamel mixed thoroughly before use. If necessary, the enamel is diluted with xylene (GOST 9410), o-xylene (N 38.101254), or with solvent (GOST 10214) in an amount of not more than 20% by weight of the enamel (depending on the application), filtered and applied as one - two layers. Increase in layers allows you to get the best performance properties of the coating. When applied by pneumatic spray enamel diluted with solvent in an amount of not more than 25% by weight of the enamel, and when applied by airless spray and brush - not more than 5% by weight of the enamel. Enamel can be applied by brush to the original viscosity. Do not use as a solvent Nefras - S4-150 / 200 (white spirit). Drying time for each enamel layer at a temperature (20 ± 2) ° C - not more than 3 hours, the dried thickness of a single coat -. At least 20 microns. Prior to the commissioning of a colored product is recommended to maintain a minimum of 7 days at a temperature (20 ± 2) ° C and a relative humidity of 80%. Enamel consumption per single-layer coating is 80 - 120 g / m2 without considering the complexity of the painted surface, application method, the color of enamel, staff development and other factors.

Another products from the category "Paints a & Lacquers"

Designed for painting rusted or partially corroded metal surfaces with thickness of rust tightly to keep up to 100 microns (0.1 mm). It is recommended to be used for painting surfaces, cleaning of whi...
Priming enamel designed for corrosion protection of metal surfaces (different steel structures, transmission towers and cell phone towers, crane trucks, window guards and so on. Etc.
It is designed for corrosion protection of ferrous metal products, operating at temperatures from -60 ° C to + 100 ° C, and operated in various environmental conditions, including the conditions of th...